обнаружил, что у нас в Intellecom используется MSCHAPv2, но все-равно не проходит авторизацию. Мой конфиг

BandwidthMHz                      5 7 8.75 10

ScanMinFrequencyMHz               2300
ScanMaxFrequencyMHz               2400
ScanStepFrequencyMHz              0.25

NetworkSearchTimeoutSec              60

NetworkEntryTimeoutSec               10

AuthEnabled                       Yes

# EAP Method (Type: Integer). Valid values are:
#   0 = EAP-TTLS/MSCHAPv2
#   1 = EAP-TTLS/MSCHAPv2 with device certificate
#   2 = EAP-TTLS/CHAP
#   3 = EAP-TTLS/EAP-TLS (not recommended)
#   4 = EAP-TLS
#   5 = EAP-TTLS/CHAP with device certificate
#   6 = EAP-TTLS/PAP
#   7 = EAP-TTLS/PAP with device certificate

EAPMethod                         1

UserIdentity                      'блаблабла@wimax.intellecom.ua'
TTLSAnonymousIdentity           '{am=1}anonymous@wimax.intellecom.ua'
UserPassword                      'блаблабла'  # we only do TLS for now

ValidateServerCert                Yes

#CACertPath                       '/lib/firmware'
CACertPath                        '/etc/ssl/certs'

CACertFileName                    '/etc/ssl/certs/CC_AAA.pem'

# Special options required by some base stations (Type: Boolean)
InvertMSKByteOrder                No
AlwaysIncludeTLSLength            No

# Maximum EAP fragment size, bytes (should normally be set < 1400 bytes)
EAPFragmentMaxLength              1398

# EAP supplicant polling interval (Type: Integer, Units: ms)
#    - Reduce this value to speed up the supplicant's response.
#    - Values smaller than 3 ms are not recommended.
EAPPollingLoopIntervalMs          100

# Enable Inner NAI (phase 2 user identity) modification by firmware (Type: Boolean)
InnerNAIChange                                    No

BeceemEngineFileName              '/lib/libengine_beceem.so'

AutoReConnectIntervalSec          2
AutoReDisconnectIntervalSec       20

LinkStatusRequestPeriodSec        2

IPRefreshCommand                  'dhclient eth1 &'
NetEntryIPRefreshEnabled                No
TerminateDHCPClient                     No

FirmwareFileName                  '/lib/firmware/macxvi200.bin'
ConfigFileName                    '/lib/firmware/macxvi.cfg'
#-sprint.cfg'
# CM Server debug log level (Type: Integer)
#   Valid values:
#      0 = Off
#      1 = Errors only
#      2 = Normal
#      3 = Verbose
#      4 = Debug    
CSCMDebugLogLevel                 2

CSCMDebugLogFileName              '/tmp/CM_Server_Debug.log'
CSCMDebugLogFileMaxSizeMB       1

# ------------------------ CM Server Authentication Log ----------------------
# Authentication log level (Type: Integer)
#   Valid values are:
#       0 = Off
#       1 = Error
#       2 = Warning
#       3 = Information
#       4 = Debug
#       5 = Message dump
AuthLogLevel                      5

AuthLogFileName                   '/tmp/CM_Auth.log'
AuthLogFileMaxSizeMB            1

EngineLoggingEnabled              Yes
EngineLogFileMaxSizeMB          1

EngineLogFileName                 '/tmp/CM_Engine.log'
MACLoggingEnabled                 No
MacLogFileName                    '/tmp/CM_MacMsg.dat'